Status of This Memo

This is an Internet Standards Track document.¶

This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 7841.¶

Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at https://www.rfc-editor.org/info/rfc9655.¶

Copyright Notice

Copyright (c) 2024 IETF Trust and the persons identified as the document authors. All rights reserved.¶

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶

Table of Contents

1. Introduction

Segment routing supports the creation of explicit paths by using one or more Link-State IGP Segments or BGP Segments defined in [RFC8402]. In certain use cases, the TE paths are built using mechanisms described in [RFC9256] by stacking the labels that represent the nodes and links in the explicit path. Controllers are often deployed to construct paths across multi-domain networks. In such deployments, the headend routers may have the link-state database of their domain and may not be aware of the FEC associated with labels that are used by the controller to build paths across multiple domains. A very useful Operations, Administration, and Maintenance (OAM) requirement is to be able to ping and trace these paths.¶

[RFC8029] describes a simple and efficient mechanism to detect data plane failures in MPLS Label Switched Paths (LSPs). It defines a probe message called an "MPLS echo request" and a response message called an "MPLS echo reply" for returning the result of the probe. SR-related extensions for these are specified in [RFC8287]. [RFC8029] provides mechanisms primarily to validate the data plane and secondarily to verify the consistency of the data plane with the control plane. It also provides the ability to traverse Equal-Cost Multipaths (ECMPs) and validate each of the ECMP paths. The Target FEC Stack TLV [RFC8029] contains sub-TLVs that carry information about the label. This information gets validated on each node for traceroute and on the egress for ping. The use of the Target FEC Stack TLV requires all nodes in the network to have implemented the validation procedures, but all intermediate nodes may not have been upgraded to support validation procedures. In such cases, it is useful to have the ability to traverse the paths in ping/traceroute mode without having to obtain the FEC for each label.¶

A simple MPLS echo request/reply mechanism allows for traversing the SR Policy path without validating the control plane state. [RFC8029] supports this mechanism with FECs like the Nil FEC and the Generic FECs (i.e., Generic IPv4 prefix and Generic IPv6 prefix). However, there are challenges in reusing the Nil FEC and Generic FECs for validation of SR Policies [RFC9256]. The Generic IPv4 prefix and Generic IPv6 prefix FECs are used when the protocol that is advertising the label is unknown. The information that is carried in the Generic FECs is the IPv4 or IPv6 prefix and prefix length. Thus, the Generic FEC types perform an additional control plane validation. However, the Generic FECs and relevant validation procedures are not thoroughly detailed in [RFC8029]. The use case mostly specifies inter-AS (Autonomous System) VPNs as the motivation. Certain aspects of SR, such as anycast Segment Identifiers (SIDs), require clear guidelines on how the validation procedure should work. Also, the Generic FECs may not be widely supported, and if transit routers are not upgraded to support validation of Generic FECs, traceroute may fail. On the other hand, the Nil FEC consists of the label, and there is no other associated FEC information. The Nil FEC is used to traverse the path without validation for cases where the FEC is not defined or routers are not upgraded to support the FECs. Thus, it can be used to check any combination of segments on any data path. The procedures described in [RFC8029] are mostly applicable when the Nil FEC is used as an intermediate FEC in the FEC stack. Challenges arise when all labels in the label stack are represented using the Nil FEC.¶

Section 2 discusses the problems associated with using the Nil FEC in an MPLS ping/traceroute procedure, and Sections 3 and 4 discuss simple extensions needed to solve the problem.¶

The problems and the solutions described in this document apply to the MPLS data plane. Segment Routing over IPv6 (SRv6) is out of scope for this document.¶

2. Problem with Nil FEC

The purpose of the Nil FEC, as described in [RFC8029], is to ensure that transit tunnel information is hidden and, in some cases, to avoid false negatives when the FEC information is unknown.¶

This document uses a Nil FEC to represent the complete label stack in an MPLS echo request message in ping and traceroute mode. A single Nil FEC is used in the MPLS echo request message irrespective of the number of segments in the label stack. Section 4.4.1 of [RFC8029] notes:¶

If the outermost FEC of the Target FEC stack is the Nil FEC, then the node MUST skip the Target FEC validation completely.¶

When a router in the label stack path receives an MPLS echo request message, there is no definite way to decide whether it is the intended egress router since the Nil FEC does not carry any information and no validation is performed by the router. Thus, there is a high possibility that the packet may be misforwarded to an incorrect destination but the MPLS echo reply might still return success.¶

To mitigate this issue, it is necessary to include additional information, along with the Nil FEC, in the MPLS echo request message in both ping and traceroute modes and to perform minimal validation on the egress/destination router. This will enable the router to send appropriate success and failure information to the headend router of the SR Policy. This supplementary information should assist in reporting transit router details to the headend router, which can be utilized by an offline application to validate the traceroute path.¶

Consequently, the inclusion of egress information in the MPLS echo request messages in ping and traceroute modes will facilitate the validation of the Nil FEC on the egress router, ensuring the correct destination. Egress information can be employed to verify any combination of segments on any path without requiring upgrades to transit nodes. The Egress TLV can be silently dropped if not recognized; alternately, it may be stepped over, or an error message may be sent (per [RFC8029] and the clarifications in [RFC9041] regarding code points in the range 32768-65535).¶

If a transit node does not recognize the Egress TLV and chooses to silently drop or step over the Egress TLV, the headend will continue to send the Egress TLV in the next echo request message, and if egress recognizes the Egress TLV, egress validation will be executed at the egress. If a transit node does not recognize the Egress TLV and chooses to send an error message, the headend will log the message for informational purposes and continue to send echo requests with the Egress TLV, with the TTL incremented. If the egress node does not recognize the Egress TLV and chooses to silently drop or step over the Egress TLV, egress validation will not be done, and the ping/traceroute procedure will proceed as if the Egress TLV were not received.¶

3. Egress TLV

The Egress TLV MAY be included in an MPLS echo request message. It is an optional TLV and, if present, MUST appear before the Target FEC Stack TLV in the MPLS echo request packet. This TLV can only be used in LSP ping/traceroute requests that are generated by the headend node of an LSP or SR Policy for which verification is performed. In cases where multiple Nil FECs are present in the Target FEC Stack TLV, the Egress TLV must be added corresponding to the ultimate egress of the label stack. Explicit paths can be created using Node-SID, Adj-SID, Binding SID, etc. The Address field of the Egress TLV must be derived from the path egress/destination. The format is as specified in Figure 1.¶

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |      Type = 32771 (Egress TLV)  |          Length             |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                      Address (4 or 16 octets)                 |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Type:

32771 (Section 6.1)¶

Length:

Variable (4 octets for IPv4 addresses and 16 octets for IPv6 addresses). Length excludes the length of the Type and Length fields.¶

Address:

This field carries a valid 4-octet IPv4 address or a valid 16-octet IPv6 address. The address can be obtained from the egress of the path and corresponds to the last label in the label stack or the SR Policy Endpoint field [SR-POLICY-BGP].¶

4. Procedure

This section describes aspects of LSP ping and traceroute operations that require further considerations beyond those detailed in [RFC8029].¶

                  ----R3----
                 /  (1003)  \
      (1001)    /            \(1005)     (1007)
        R1----R2(1002)        R5----R6----R7(address X)
                \            /     (1006)
                 \   (1004) /
                  ----R4----

5. Backward Compatibility

The extensions defined in this document are backward compatible with the procedures described in [RFC8029]. A router that does not support the Egress TLV will ignore it and use the Nil FEC procedures described in [RFC8029].¶

When the egress node in the path does not support the extensions defined in this document, egress validation will not be done, and Best-return-code will be set to 3 ("Replying router is an egress for the FEC at stack-depth <RSC>") and Best-rtn-subcode to stack-depth in the MPLS echo reply message.¶

When the transit node in the path does not support the extensions defined in this document, Best-return-code will be set to 8 ("Label switched at stack-depth <RSC>") and Best-rtn-subcode to Label-stack-depth to report transit switching in the MPLS echo reply message.¶

6. IANA Considerations

7. Security Considerations

This document defines an additional TLV for MPLS LSP ping and conforms to the mechanisms defined in [RFC8029]. All the security considerations defined in [RFC8287] apply to this document. This document does not introduce any additional security challenges to be considered.¶

Acknowledgements

The authors would like to thank Stewart Bryant, Greg Mirsky, Alexander Vainshtein, Sanga Mitra Rajgopal, and Adrian Farrel for their careful review and comments.¶

Authors' Addresses