Network Working Group J. Myers Request for Comments: 1734 Carnegie Mellon Category: Standards Track December 1994 POP3 AUTHentication command Status of this Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. 1. Introduction This document describes the optional AUTH command, for indicating an authentication mechanism to the server, performing an authentication protocol exchange, and optionally negotiating a protection mechanism for subsequent protocol interactions. The authentication and protection mechanisms used by the POP3 AUTH command are those used by IMAP4. 2. The AUTH command AUTH mechanism Arguments: a string identifying an IMAP4 authentication mechanism, such as defined by [IMAP4-AUTH]. Any use of the string "imap" used in a server authentication identity in the definition of an authentication mechanism is replaced with the string "pop". Restrictions: may only be given in the AUTHORIZATION state Discussion: The AUTH command indicates an authentication mechanism to the server. If the server supports the requested authentication mechanism, it performs an authentication protocol exchange to authenticate and identify the user. Optionally, it also negotiates a protection mechanism for subsequent protocol interactions. If the requested authentication mechanism is not supported, the server Myers [Page 1] RFC 1734 POP3 AUTH December 1994 should reject the AUTH command by sending a negative response. The authentication protocol exchange consists of a series of server challenges and client answers that are specific to the authentication mechanism. A server challenge, otherwise known as a ready response, is a line consisting of a "+" character followed by a single space and a BASE64 encoded string. The client answer consists of a line containing a BASE64 encoded string. If the client wishes to cancel an authentication exchange, it should issue a line with a single "*". If the server receives such an answer, it must reject the AUTH command by sending a negative response. A protection mechanism provides integrity and privacy protection to the protocol session. If a protection mechanism is negotiated, it is applied to all subsequent data sent over the connection. The protection mechanism takes effect immediately following the CRLF that concludes the authentication exchange for the client, and the CRLF of the positive response for the server. Once the protection mechanism is in effect, the stream of command and response octets is processed into buffers of ciphertext. Each buffer is transferred over the connection as a stream of octets prepended with a four octet field in network byte order that represents the length of the following data. The maximum ciphertext buffer length is defined by the protection mechanism. The server is not required to support any particular authentication mechanism, nor are authentication mechanisms required to support any protection mechanisms. If an AUTH command fails with a negative response, the session remains in the AUTHORIZATION state and client may try another authentication mechanism by issuing another AUTH command, or may attempt to authenticate by using the USER/PASS or APOP commands. In other words, the client may request authentication types in decreasing order of preference, with the USER/PASS or APOP command as a last resort. Should the client successfully complete the authentication exchange, the POP3 server issues a positive response and the POP3 session enters the TRANSACTION state. Possible Responses: +OK maildrop locked and ready -ERR authentication exchange failed Myers [Page 2] RFC 1734 POP3 AUTH December 1994 Examples: S: +OK POP3 server ready C: AUTH KERBEROS_V4 S: + AmFYig== C: BAcAQU5EUkVXLkNNVS5FRFUAOCAsho84kLN3/IJmrMG+25a4DT +nZImJjnTNHJUtxAA+o0KPKfHEcAFs9a3CL5Oebe/ydHJUwYFd WwuQ1MWiy6IesKvjL5rL9WjXUb9MwT9bpObYLGOKi1Qh S: + or//EoAADZI= C: DiAF5A4gA+oOIALuBkAAmw== S: +OK Kerberos V4 authentication successful ... C: AUTH FOOBAR S: -ERR Unrecognized authentication type Note: the line breaks in the first client answer are for editorial clarity and are not in real authentica- tors. Myers [Page 3] RFC 1734 POP3 AUTH December 1994 3. Formal Syntax The following syntax specification uses the augmented Backus-Naur Form (BNF) notation as specified in RFC 822. Except as noted otherwise, all alphabetic characters are case- insensitive. The use of upper or lower case characters to define token strings is for editorial clarity only. Implementations MUST accept these strings in a case-insensitive fashion. ATOM_CHAR ::= atom_specials ::= "(" / ")" / "{" / SPACE / CTLs / "%" / "*" / <"> / "\" auth ::= "AUTH" 1*(SPACE / TAB) auth_type *(CRLF base64) CRLF auth_type ::= 1*ATOM_CHAR base64 ::= *(4base64_CHAR) [base64_terminal] base64_char ::= "A" / "B" / "C" / "D" / "E" / "F" / "G" / "H" / "I" / "J" / "K" / "L" / "M" / "N" / "O" / "P" / "Q" / "R" / "S" / "T" / "U" / "V" / "W" / "X" / "Y" / "Z" / "a" / "b" / "c" / "d" / "e" / "f" / "g" / "h" / "i" / "j" / "k" / "l" / "m" / "n" / "o" / "p" / "q" / "r" / "s" / "t" / "u" / "v" / "w" / "x" / "y" / "z" / "0" / "1" / "2" / "3" / "4" / "5" / "6" / "7" / "8" / "9" / "+" / "/" ;; Case-sensitive base64_terminal ::= (2base64_char "==") / (3base64_char "=") CHAR ::= continue_req ::= "+" SPACE base64 CRLF CR ::= CRLF ::= CR LF CTL ::= Myers [Page 4] RFC 1734 POP3 AUTH December 1994 LF ::= SPACE ::= TAB ::= 4. References [IMAP4-AUTH] Myers, J., "IMAP4 Authentication Mechanisms", RFC 1731, Carnegie Mellon, December 1994. 5. Security Considerations Security issues are discussed throughout this memo. 6. Author's Address John G. Myers Carnegie-Mellon University 5000 Forbes Ave Pittsburgh, PA 15213 EMail: jgm+@cmu.edu Myers [Page 5]